- Which part of wire is positive?
- What happens if you wire live and neutral wrong?
- Which is pin 1 on rj45?
- Do you hook up negative or positive first?
- Which side of the plug is positive and negative?
- Can I connect white and black wires together?
- What happens if you switch hot and neutral wires?
- What happens if you connect the negative terminal first?
- Which wire should be connected first?
- Which pins are used for Ethernet?
- Do you hook up red or black first?
- Does it matter which wire goes where on a lamp?
- What does black tape on a white wire mean?
- What are the 3 types of connectors?
- Does Ethernet use all 4 pairs?
- What 4 wires are used in cat5?
- What happens if I connect positive to negative?
- How do I tell positive and negative wires?
Which part of wire is positive?
The solid/dashed lines on wires like the ones pictured in your question are used to indicate polarity e.g.
for the “wall wart” power supplies.
Usually* the wire with the white stripe or the dashed lines carries the “positive” (+) end, while the other, unmarked wire carries the “negative” (-) end..
What happens if you wire live and neutral wrong?
If the switch is put in the neutral line (like in your house) the switch and fuse comes in neutral line. In the switch OFF position the entire appliance will have 220V, touching any part will give you deadly shock. As per the rules, if live and neutral are reversed, Electricity board will not give power to your house.
Which is pin 1 on rj45?
When looking at an RJ45 connector from its underside, the first pin is on the left-hand side and is called pin number 1. Computers use pins 1 and 2 to send information and pins 3 and 6 to receive information.
Do you hook up negative or positive first?
When disconnecting the cables from the old battery, disconnect the negative first, then the positive. Connect the new battery in the reverse order, positive then negative.” When you are replacing your car battery, It isn’t always easy to remember the order in which to disconnect and reconnect the terminals.
Which side of the plug is positive and negative?
Diagram showing positive tip polarity on the left and negative tip polarity on the right. To read diagram: The center positive drawing on the left indicates that the center (also known as the tip) of the output plug is positive (+) and the barrel (ring) of the output plug is negative (−).
Can I connect white and black wires together?
A single black and white connected together is normal. It is part of a switch loop. A black connected to a group of whites is not normal and probably should be connected to the other blacks. It is normal to have a white connected to a group of blacks if a switch loop is used.
What happens if you switch hot and neutral wires?
In North America, switching the hot and neutral wires on the AC breaker will cause a potential shock hazard with the polarized electrical outlets and lighting fixtures connected to that breaker. It’s not a good thing. You will have short circuited the breaker to the neutral, which will trip the breaker immediately.
What happens if you connect the negative terminal first?
It is only a safety issue. If you first connect the negative cable, then when you connect the positive cable there is a chance the wrench will complete a circuit between the battery and the chassis of the car. … If the battery is offgassing, the spark could ignite those gases causing an explosion.
Which wire should be connected first?
Ideally you would connect any ground cables first as that ensures that it is safe to move on and around the equipment ant that you can safely work on all parts, then connect the zero wire followed by the phases.
Which pins are used for Ethernet?
The RJ45 data cables we use to connect computers to a Ethernet switch is straight-through cables. As noted above, the RJ45 cable uses only 2-pairs of wires: Orange (pins 1 & 2) and Green (pins 3 & 6). Pins 4, 5 (Blue) and 7, 8 (Brown) are NOT used.
Do you hook up red or black first?
Connect the positive end first. Attach the red/positive (+) cable to the red/positive (+) battery post and tighten with a wrench. Do the same on the black/negative (-) side. Ensure that the connections on both ends are secure by trying to move the battery around.
Does it matter which wire goes where on a lamp?
True, the lamp will usually work either way. … Remember when repairing lamps, the neutral wire in the lamp cord is marked (usually with a rib or ribs) and it connects to the wide blade of the plug at one end and to the neutral screw (usually silver but may have some other identification) at the other end.
What does black tape on a white wire mean?
When a white wire is augmented with a red or black color marking, this often indicates that it is being used as a hot wire rather than a neutral wire. … This white wire should be looped several times around with black electrical tape to show that it is being used for something other than a neutral.
What are the 3 types of connectors?
There are three types cable connectors in a basic cabling installation techniques: twisted-pair connectors,coaxial cable connectors and fiber-optic connectors. Generally cable connectors have a male component and a female component, except in the case of hermaphroditic connectors such as the IBM data connector.
Does Ethernet use all 4 pairs?
Gigabit Ethernet Introduction Ethernet Cat 5 cables have eight wires (four pairs), but under 10BaseT and 100BaseT standards (10 Mbps and 100 Mbps, respectively) only four (two pairs) of these wires are actually used. One pair is used for transmitting data and the other pair is used for receiving data.
What 4 wires are used in cat5?
These are just a few and it depends on the brand you buy. The four wire pairs in a CAT-5 cable are distinguished by the color of their insulation. The four colors are (in order) blue, orange, green and brown. Thus, when refering to the “second pair” of wires, it is the orange pair.
What happens if I connect positive to negative?
Connecting the positive terminal of each battery to the negative terminal of the other battery will result in a huge surge of electrical current between the two batteries. … The heat can melt internal and external battery parts, while the pressure from the hydrogen gas can crack the battery casing.
How do I tell positive and negative wires?
If you have a wire where both sides are the same color, which is typically copper, the strand that has a grooved texture is the negative wire. Run your fingers along the wire to determine which side has the ribbing. Feel the other wire which is smooth. This is your positive wire.